QX-MOTOR A32-160A 6-14S Brushless ESC (160A / OPTO)
The QX-MOTOR A32-160A is an industrial-grade, high-voltage brushless electronic speed controller engineered for heavy-lift multi-rotors, agricultural UAVs, and large ducted fans (EDF). Powered by a 32-bit ARM processing architecture and wrapped in a CNC-machined aluminum heatsink housing, it delivers continuous 160A throughput with comprehensive onboard electronic protections.
Specifications
| Model | A32-160A-14S |
| Input Voltage | 16.8V – 58.8V (6S – 14S LiPo) |
| Continuous Current | 160A |
| BEC Output | None (OPTO / External UBEC or FC power required) |
| PWM Drive Frequency | 16 kHz |
| Dimensions | 87.5 × 43 × 27.5 mm |
| Mounting Hole Pattern | 81 × 35 mm (3.0 mm / M3 aperture) |
| Weight | 189g (including leads) |
| Throttle Calibration | Automatic startup throttle position detection |
Before you buy
- OPTO — there is no BEC. You must power the receiver/servos separately, from a UBEC or the flight controller.
- 6–14S input (16.8–58.8 V) — 14S is a high-voltage setup; make sure every connector and capacitor in the chain is rated for it.
- 160 A continuous at 189 g — this is an EDF/fixed-wing ESC, not a multirotor part.
- 16 kHz PWM drive suits high-KV ducted-fan motors; a low-KV outrunner on 16 kHz may run rough.
- Automatic throttle calibration on startup — do not hold throttle at power-up, it will calibrate to that position.
In the box
- 1 × QX-MOTOR A32-160A 6-14S Brushless ESC (Black or Grey per variant selection)
Why this spec
- 32-Bit Microprocessor: High-speed ARM processing core ensures fast throttle response and linear speed curve regulation.
- High-Voltage Architecture: Operates natively on 6S to 14S LiPo power packs (16.8V – 58.8V) for high-efficiency drone propulsion systems.
- Optocoupler Signal Isolation: Long throttle input lead uses dedicated optocoupler isolation to suppress high-current electromagnetic interference (EMI).
- Comprehensive Safety Suite: Integrated low-voltage protection (3.1V/cell threshold), thermal derating (cuts power 50% above 140°C), throttle loss cutoff (2-second fail-safe), and motor stall protection.
- CNC Heatsink Enclosure: Finned aluminum case provides passive thermal dissipation and secure M3 chassis mounting.
What you still need to complete the build
- A flight controller with the matching harness
- Motors within the ESC current rating
- A capacitor across the battery pads
Support and returns
Covered against manufacturing defects for 12 months — bearings, windings and bell balance. If a motor arrives with a bent shaft, a rubbing bell or a dead phase, contact us with the order number and a photo and we replace it. Crash damage, burnt windings from a stalled prop and water ingress are not covered.
Frequently Asked Questions
How do I choose the correct version?
Available selections for this listing: QX160A(6-14S) / 87.5*43*27.5. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.
Does every option include both a flight controller and an ESC?
No such assumption should be made. Check the selected option and package contents to distinguish standalone boards, ESCs and complete stacks.
How do I check the supported battery voltage?
Use the voltage range for the exact selected board or stack. For a stack, the usable input must stay within the limits of every connected component, not only the ESC.
Are matching-looking connectors plug-and-play?
Compare the pinout, voltage, ground, signal order and connector orientation on both devices. The same connector housing does not guarantee matching wiring.
Which firmware target should I use?
Use the manufacturer’s exact board revision and supported firmware target. Do not flash a target based solely on the processor name or a similar product title.
Is the current rating a guarantee for my installation?
No. Check whether the published value is continuous or burst, whether it applies per channel, and the required airflow and cooling conditions. Size the system using the actual motor and propeller load.
How should I perform initial setup?
Remove propellers, verify soldering and polarity, and follow the board manufacturer’s setup procedure. Check control direction, motor mapping and failsafe before flight.