BrotherHobby LPD 2806.5 Brushless Motor
The BrotherHobby LPD 2806.5 is a performance brushless motor engineered for 6- to 7-inch long-range and freestyle FPV multirotors. Built with a hard-anodized 7075 aluminum alloy bell, N52H curved neodymium magnets, Japanese NMB bearings, and a titanium alloy hollow shaft.
Specifications
| Stator Size | 2806.5 (28mm diameter × 6.5mm height) |
| Bell & Base Material | 7075 Aluminum Alloy |
| Shaft Material | Titanium Alloy Hollow Shaft |
| Propeller Shaft Thread | M5 |
| Magnets | N52H Curved Neodymium |
| Bearings | Japanese NMB |
| Rated Operating Voltage | 6S LiPo (tested on 6S bench platform) |
| Available KV Options | 1300KV, 1700KV (tested as 1304KV / 1690KV) |
Before you buy
- 2806.5 on 6S: 1300KV is 7-inch long-range, 1700KV is 6-inch or 5-inch race. Do not put 1700KV on a 7-inch prop at 6S.
- Tested values are 1304KV and 1690KV — the listing rounds; expect ±3% against the label.
- Titanium hollow shaft, M5 thread — light and strong, but a prop strike can still bend it.
- Japanese NMB bearings are the reason to choose this over a generic 2806.5.
- 19 × 19 mm M3 mounting — check the arm pattern.
In the box
- 1 × BrotherHobby LPD 2806.5 Brushless Motor
- 4 × M3 Mounting Screws
- 1 × M5 Propeller Nut
Why this spec
- Aviation-grade 7075 aluminum bell and base with durable hard-anodized finish
- N52H curved neodymium magnets engineered for smooth, linear throttle response
- Titanium alloy hollow shaft providing high tensile strength with reduced rotational mass
- Japanese NMB bearings for smooth spinning characteristics and extended operating life
- Ultra-thin non-oriented silicon steel laminations for reduced eddy current losses
- High-fill copper windings
Bench test records conducted on manufacturer platform at 100% throttle for 30 seconds (28°C ambient). Values are indicative and vary with ambient air and battery state.
| KV Variant | Tested Propeller | ESC & Voltage | Throttle | Current | RPM | Thrust | Power | Efficiency | Winding Temp (30s) |
|---|---|---|---|---|---|---|---|---|---|
| 1300KV (1304KV tested) | HQ 7.0×3.5 3-Blade Nylon | 6S 50A (24.0V / 23.8V) | 50% 100% |
7.2A 44.4A |
12,132 21,691 |
750 gf 2,520 gf |
172.8W 1,056.7W |
4.34 gf/W 2.38 gf/W |
-- 102.2°C |
| 1700KV (1690KV tested) | HQ 6.0×4.0 3-Blade Nylon | 6S 50A (24.0V / 23.8V) | 50% 100% |
10.6A 49.2A |
17,193 29,610 |
840 gf 2,440 gf |
254.4W 1,170.9W |
3.30 gf/W 2.08 gf/W |
-- 109.8°C |
What you still need to complete the build
- A frame with the matching motor hole pattern
- ESCs or a 4-in-1 sized for the prop and cell count
- Props matched to the KV
- Locking compound for the motor screws
Support and returns
Covered against manufacturing defects for 12 months — bearings, windings and bell balance. If a motor arrives with a bent shaft, a rubbing bell or a dead phase, contact us with the order number and a photo and we replace it. Crash damage, burnt windings from a stalled prop and water ingress are not covered.
Frequently Asked Questions
How do I choose the correct version?
Available selections for this listing: 1300KV; 1700KV. Select the exact configuration required for your build; specifications for one selection do not automatically apply to the others.
How do I choose the correct KV?
Choose the exact KV using motor test data for your intended battery voltage and propeller. KV alone does not determine thrust, efficiency or suitability for a particular aircraft.
Will this motor fit my frame and propeller?
Compare mounting-hole spacing, screw thread and depth, shaft or hub dimensions and available clearance with your frame and propeller. Similar stator sizes do not guarantee identical mounting.
How should I size the ESC and battery?
Use measured current for the selected motor, voltage and propeller combination, then check ESC thermal limits, battery current capability and connector ratings. Do not treat peak test figures as continuous-use guarantees.
Are thrust figures valid for every version?
No. Thrust and current depend on the exact KV, voltage, propeller and test conditions. Use only data that matches the selected configuration.
What should I check before the first run?
Verify screw clearance from the windings, secure the motor and wiring, and check rotation with propellers removed. Stop if there is binding, unusual vibration or abnormal heating.